Thermal paste and thermal pads should be replaced when they are damaged, dried out, or no longer transfer heat properly. Replacement timing depends on the computer’s condition and the manufacturer’s recommendations.
Thermal paste fills microscopic unevenness between the processor and the heatsink, while thermal pads transfer heat from other components. They are different materials, and replacing them “while you’re at it” is not always necessary: pad thickness matters for proper contact. This article explains how to tell what to replace and when.
| Criterion | Thermal paste | Thermal pad |
|---|---|---|
| Gap | Thin, between the chip and heatsink | A gap that needs to be bridged |
| Typical components | Processor and graphics chip | Memory and other chips |
| Heat transfer | Usually higher | Usually lower |
| Installation | Must be applied evenly | Easy to install; does not spread |
| Electrical conductivity | Some types conduct electricity | Does not conduct electricity |
- 0,1-0,3 миллиметра gap in which a thermal plate can create additional physical stress
- до 10 Вт/мК stated thermal conductivity of thermal paste
- 5,6 Вт/мК stated thermal conductivity of Deepcool thermal paste
- 8,5 Вт/мК stated thermal conductivity of Zalman thermal paste
What carries heat away from the processor and graphics card?
A heatsink carries heat away from the processor and graphics chip, while thermal paste or a thermal pad helps transfer it from the component to the cooling system.
Thermal paste fills microscopic imperfections between the chip and the heatsink base. A processor and graphics chip need close contact with the heatsink, so paste is generally used here: it usually transfers heat better than a pad.
A thermal pad is a ready-made, flexible layer that bridges the gap between a component and the cooling system. It is more often used on memory chips and other parts that need to connect to the heatsink across a gap. A pad does not spread or conduct electricity, but it usually transfers heat less effectively than paste.
How to choose a thermal interface
- Thermal paste — for close contact between a processor or graphics chip and the heatsink base.
- Thermal pad — for memory chips and other parts when there is a gap between them and the cooling system.
With a gap of 0,1-0,3 millimeters, a thermal plate can create additional physical stress on component packages. Before installation, check the gap thickness and the type of thermal interface specified for that particular assembly.
How does thermal paste differ from a thermal pad?
Thermal paste fills imperfections in the thin gap between a chip and its cooler, while a thermal pad bridges a noticeable gap through its own thickness.
Choose the material based on the gap
Paste is suitable for a processor or graphics processor when the cooling system is designed for it: it fills microscopic imperfections without adding thickness. Thermal paste is quoted as having thermal conductivity of up to 10 Вт/мК; thermal pads have lower conductivity.
- Thermal paste — for close contact between a chip and its cooler when no separate layer of a specified thickness is needed between them.
- Thermal pad — for a noticeable gap, such as between a memory chip and a heatsink. Choose it based not only on thermal conductivity but also on thickness: the pad should compress and make contact with both surfaces.
A thermal pad is easier to install: it does not spread. But ease of installation does not make it a universal replacement for paste on a processor or GPU. The cooling system’s design determines the choice — the distance between the chip and heatsink and the type of contact intended for it. Before replacing anything, check which thermal interface is installed and what layer is required.
How to choose a material based on the gap and thermal conductivity
Choose a material according to the design of the assembly: a processor usually uses thermal paste, while a graphics card’s memory chips may have thermal pads.
- Gap. At a distance of 0,1-0,3 millimeters, a thermal pad can create additional physical stress on component packages. Choose the thickness based on the device documentation or the pad that was installed: the wrong thickness will compromise contact.
- Thermal conductivity. Thermal paste is listed as having a rating of up to 10 Вт/мК — thermal pads do not reach that level. Ratings also vary between individual products: 5,6 Вт/мК for Deepcool and 8,5 Вт/мК for Zalman. This compares only these figures, not all products from the brands.
How to match the material to the component
Thermal paste is suitable for a processor when it is what the design calls for: it is applied between the chip and the heatsink. A thermal pad is needed where the design calls for a pad to fill a gap, for example, on a graphics card’s memory chips.
Before buying a thermal pad, first check its thickness against the device documentation or the pad you removed. Thermal conductivity alone is not enough: if the thickness is wrong, contact between the component and cooling system will be compromised.
When can temperature and noise indicate a problem?
High temperatures combined with louder fans and reduced performance may indicate a cooling problem, but they do not prove that the thermal paste has dried out.
Check for dust and fan problems first.
Dust in the heatsink impedes heat dissipation, while a faulty fan or poor case ventilation can cause overheating even when the thermal interface is fine. So before replacing the paste, check whether dust is clogging the heatsink fins and whether the fans are spinning.
- Dust in the heatsink: check whether it is blocking the airflow.
- Fans: make sure they are working and that the noise is not accompanied by them stopping.
- Thermal paste and thermal pads: consider replacing them if other causes have been ruled out or the cooling system has been disassembled.
If the computer shuts down under load, check the entire cooling system and the device’s condition, not just the thermal interface. The shutdown may be caused by dust, ventilation, or fan operation rather than the paste.
Compare the computer’s temperature and behavior under the same workload — for example, in the same game or program. A single reading without such a comparison cannot tell you whether the paste has dried out. Usage time, workload, and ventilation conditions should be comparable.
When should you replace a thermal interface, and why avoid opening up a computer for preventive maintenance?
Replace thermal paste when you remove the heatsink or see signs of impaired cooling, not simply because a year or two has passed.
If the cooling system has not been disassembled and the processor or graphics card temperature, fan noise, and performance have not changed, there is no need to replace the paste as a precaution. Go by these signs, not the calendar.
When to replace thermal pads
Replace thermal pads if they are damaged or have deteriorated and no longer ensure close contact between the component and heatsink. Do not remove them without a reason: a pad can shift when reinstalled, leaving the cooling system improperly seated.
- The heatsink has not been removed, and cooling is working as usual: leave the thermal paste and pads in place.
- A pad is torn, deformed, or has noticeably lost its elasticity: check that the replacement is the right thickness and install it in place of the damaged pad.
- The heatsink has been removed: thermal paste is usually reapplied, while pads should be checked for damage and displacement.
Any disassembly carries a risk of damaging the mounts, shifting a thermal pad, or reassembling the cooling system incorrectly. If you are not sure how to remove the heatsink and apply paste, it is safer to have a service center do the work.
Frequently asked questions
Can I use a thermal pad instead of thermal paste on a processor?
Do I need to replace thermal paste every year?
Why is my computer noisy and overheating after replacing the paste?
How do I find out what thickness thermal pad my graphics card needs?
Sources
- club.dns-shop.ru — “What Are Thermal Pads?”
- zip-2002.ru — “Which Is Better”
- ozon.ru — “Rating of the Best Thermal Pastes and Thermal Pads for Computers”
- allpc.by — “Replacing Thermal Paste in a Laptop or PC: When It’s Needed”
- computer-master.org — “Choosing a Thermal Interface: Thermal Paste or Thermal Pad”
